Product

 

 

1. Mix Part A and Part B components according to recommended weight ratios. If power equipment is to be used, it is generally recommended to keep mixing speed at or below 350 rpm to prevent heat buildup, which can cause loss of working time and premature curing of the rubber. It is recommended that the container be filled to not more than 1/3 the container height to allow sufficient room for expansion during the deaeration procedure.

2. For these products requiring deaeration, place mixed material in a vacuum chamber and exert 29 inches Vacuum on the material. Some products will require that the vacuum be interrupted or "bumped" several times before the material crests and falls by itself. After the material has receded, keep the mixed material under full vacuum for a minimum of 15 minutes. Bleed air slowly into the chamber until atmospheric equilibrium is reached. Remove mixed and vacuumed material from the chamber. The material is now ready for pouring.

3. Some Bluestar Silicones Aerospace and Industrial products have a very long mixed pot life. Storing the mixture in a tightly sealed container at 0°F (-18°C) may extend the pot life even longer. Care should be taken when using this method to prevent moisture from condensing on the inside of cold containers and contaminating the mixture.  

Avoid discharge into drains, water courses or onto the ground. Store in a cool, dry place with adequate ventilation. Keep away from incompatible materials, open flames, and high temperatures. Avoid contact with oxidizing agents. Suitable containers: Steel drums coated with epoxy-resin.请查阅这个产品的物质安全数据表

BLUESIL V-695 A

BLUESILV-695 is a black, two component addition cure, flowable silicone aerospace sealant

for the use as an abradable air seal for compressor blades of jet engines. BLUESILV-695 imparts high thermal stability, good machinability, long work time, and low density. It is also designed to achieve optimum properties at the specified elevated temperature cure schedule.

Kit Matching: Many Bluestar Silicones Aerospace and Industrial products are kit matched when manufactured. These products should be processed using the specific matched Part A and Part B units supplied with the kit. Using a different lot of Part A or Part B may affect the properties of the product.

衬垫

双组份室温硅橡胶

硅浆

• Abradable air seal for the compressor blades of jet engines.

中南美;北美

 Characteristics_A

 

 

粘度2400PairedCompASTM D 2196Poise

 Characteristics_B

 

 

 

 

 Table_Characteristics_A_And_B

 

 

hardness_cd523e03-72a3-4261-93f9-36f7bbeeafb1hardness_cd523e03-72a3-4261-93f9-36f7bbeeafb1硬度58.5PairedMixASTM D 2240邵氏A
elongation_68a5ddf2-2baf-4e60-ac6f-0a8a18a758b2elongation_68a5ddf2-2baf-4e60-ac6f-0a8a18a758b2延伸率150PairedMixASTM D 412%
specific-gravity_108e6684-e7c4-4e2b-a615-631b494320d3specific-gravity_108e6684-e7c4-4e2b-a615-631b494320d3比重0.73PairedMixASTM D 792
tensile-strength_e61eb2e0-4dc3-47b0-a61f-b673f1b265dctensile-strength_e61eb2e0-4dc3-47b0-a61f-b673f1b265dc抗拉强度262.5PairedMixSTM-6506psi

 

 

 

 

BLUESIL V-695 BBLUESIL V-695 B/our_offer/Product/90054264/90051140/BLUESIL-V-695-B

 

 

 

 

 NeedAnExpert

 

 

 CS

 

 

 SS

 

 

 PressRelease

 

 

 

 

 Brochures

 

 

 TDS