Product

 

 

​更详细的使用指导,请下载PDF格式的TDS。


 

BLUESIL SLT AQUARIUM TRANSLUCENT 储存温度要介于 2 °C/ 36 °F 和 30 °C/ 86 °F 之间,从生产日期开始产品保质 24 个月请查看安全数据表欧盟《电气、电子设备中限制使用某些有害物质指令》

BLUESIL SLT AQUARIUM TRANSLUCENT

BLUESIL SLT AQUARIUM单组份, 可用于有机硅弹性粘结和密封,在室温和湿气存在的条件下,能够快速固化,并达到高强度粘结的高模量有机硅弹性体,具有优异的耐候性

粘附力;密封胶;密封

脱酸型单组份室温硅橡胶

硅浆

欧盟《电气、电子设备中限制使用某些有害物质指令》

快速固化并达到优异的粘结可用于快速装配, 透明颜色的非常适用于鱼缸的使用。在玻璃、陶瓷和抛光表面不需要底涂,在其它材料(金属、木材、塑料、混泥土、石材)建议使用底涂。固化后能抵御稀酸和碱,稀释漂白,海水,盐雾。

鱼缸 (透明和黑色).

亚太区;欧洲中东非洲;中南美;北美

 Characteristics_A

 

 

硬度24MonocompISO 868邵氏A
延伸率450MonocompNF ISO 37%
抗拉强度2.5MonocompNF ISO 37MPa

 Characteristics_B

 

 

 

 

 Table_Characteristics_A_And_B

 

 

 

 

 

 

 

 

1. 固化前
密封胶类型............................................................................................... 酸性
密度, g/cm3约.....................................................................................1.04
流淌* (NF EN 27390) mm, 约.........................................................0
挤出速率(NM 495A, 3 mm/3 bars), g/min, 约.........................40
粘度(strain of 3000 N/m2, 20°C), Pa.s, 约..................................320
2. 固化中
表干时间, min, 约*. ............................................................................ 7
结皮时间* (ASTM C679-87), min., 约............................................15
固化速率*, mm / 1 天, 约..................................................................4.5
mm / 3 天,约.......................................................................................8
mm / 7 天, 约....................................................................................... 10
施工温度, °C ... ................................................................................. +5 to +40
3. 固化后
邵A硬度(ASTM D 2240), 约..............................................................24
弹性恢复率 (NF-EN 27389), %, 约..................................................100
接口位移能力 %..... ............................................................................. +/-25
工作温度, °C ...................................................................................... -50 to +200

在2mm厚的薄膜的力学性能*(NF T 46002)*
100%延伸时的模量, MPa, 约..............................................................0.6
拉伸强度, MPa, 约 ................................................................................ 2.5
断裂伸长率, %, 约 .................................................................................450



在H型试件的力学性能*(EN 28339)*
100%延伸时的模量, MPa, 约... ........................................................ 0.55
拉伸强度, MPa,约. .... ........................................................................... 1.2
断裂伸长率 % 约... ........................................................................ 250
* 温度23℃,相对湿度50%条件下。 ​1. 固化前密封胶类型............................................................................................... 酸性密度, g/cm3约.....................................................................................1.04流淌* (NF EN 27390) mm, 约.........................................................0挤出速率(NM 495A, 3 mm/3 bars), g/min, 约.........................40粘度(strain of 3000 N/m2, 20°C), Pa.s, 约..................................3202. 固化中表干时间, min, 约*. ............................................................................ 7结皮时间* (ASTM C679-87), min., 约............................................15固化速率*, mm / 1 天, 约..................................................................4.5mm / 3 天,约.......................................................................................8mm / 7 天, 约....................................................................................... 10施工温度, °C ... ................................................................................. +5 to +403. 固化后邵A硬度(ASTM D 2240), 约..............................................................24弹性恢复率 (NF-EN 27389), %, 约..................................................100接口位移能力 %..... ............................................................................. +/-25工作温度, °C ...................................................................................... -50 to +200在2mm厚的薄膜的力学性能*(NF T 46002)*100%延伸时的模量, MPa, 约..............................................................0.6拉伸强度, MPa, 约 ................................................................................ 2.5断裂伸长率, %, 约 .................................................................................450在H型试件的力学性能*(EN 28339)*100%延伸时的模量, MPa, 约... ........................................................ 0.55拉伸强度, MPa,约. .... ........................................................................... 1.2断裂伸长率 % 约... ........................................................................ 250* 温度23℃,相对湿度50%条件下。

 

 

1. 固化前
密封胶类型............................................................................................... 酸性
密度, g/cm3约.....................................................................................1.04
流淌* (NF EN 27390) mm, 约.........................................................0
挤出速率(NM 495A, 3 mm/3 bars), g/min, 约.........................40
粘度(strain of 3000 N/m2, 20°C), Pa.s, 约..................................320
2. 固化中
表干时间, min, 约*. ............................................................................ 7
结皮时间* (ASTM C679-87), min., 约............................................15
固化速率*, mm / 1 天, 约..................................................................4.5
mm / 3 天,约.......................................................................................8
mm / 7 天, 约....................................................................................... 10
施工温度, °C ... ................................................................................. +5 to +40
3. 固化后
邵A硬度(ASTM D 2240), 约..............................................................24
弹性恢复率 (NF-EN 27389), %, 约..................................................100
接口位移能力 %..... ............................................................................. +/-25
工作温度, °C ...................................................................................... -50 to +200

在2mm厚的薄膜的力学性能*(NF T 46002)*
100%延伸时的模量, MPa, 约..............................................................0.6
拉伸强度, MPa, 约 ................................................................................ 2.5
断裂伸长率, %, 约 .................................................................................450



在H型试件的力学性能*(EN 28339)*
100%延伸时的模量, MPa, 约... ........................................................ 0.55
拉伸强度, MPa,约. .... ........................................................................... 1.2
断裂伸长率 % 约... ........................................................................ 250
* 温度23℃,相对湿度50%条件下。 ​1. 固化前密封胶类型............................................................................................... 酸性密度, g/cm3约.....................................................................................1.04流淌* (NF EN 27390) mm, 约.........................................................0挤出速率(NM 495A, 3 mm/3 bars), g/min, 约.........................40粘度(strain of 3000 N/m2, 20°C), Pa.s, 约..................................3202. 固化中表干时间, min, 约*. ............................................................................ 7结皮时间* (ASTM C679-87), min., 约............................................15固化速率*, mm / 1 天, 约..................................................................4.5mm / 3 天,约.......................................................................................8mm / 7 天, 约....................................................................................... 10施工温度, °C ... ................................................................................. +5 to +403. 固化后邵A硬度(ASTM D 2240), 约..............................................................24弹性恢复率 (NF-EN 27389), %, 约..................................................100接口位移能力 %..... ............................................................................. +/-25工作温度, °C ...................................................................................... -50 to +200在2mm厚的薄膜的力学性能*(NF T 46002)*100%延伸时的模量, MPa, 约..............................................................0.6拉伸强度, MPa, 约 ................................................................................ 2.5断裂伸长率, %, 约 .................................................................................450在H型试件的力学性能*(EN 28339)*100%延伸时的模量, MPa, 约... ........................................................ 0.55拉伸强度, MPa,约. .... ........................................................................... 1.2断裂伸长率 % 约... ........................................................................ 250* 温度23℃,相对湿度50%条件下。

 NeedAnExpert

 

 

 

 

 CS

 

 

 SS

 

 

 PressRelease

 

 

 

 

 Brochures

 

 

 TDS