Product

 

 

1. Mixing the two components
The components A, B and BLUESIL ADD 11013 are mixed by weight in the above indicated ratio. The mixing can be carried out either by hand or using a low-speed electric or pneumatic mixer to minimise the introduction of air and to avoid any temperature increase.
It is also possible to use a special mixing and dispensing machine for the two silicone components. Further information is available upon request.
2. Degassing
The mixture should be degassed preferably at 30 to 50 mbar to eliminate any entrapped air. If a dispensing machine is used, the two components are degassed separately prior to mixing.
The silicone mixture expands to times of its initial volume and bubbles rise to the surface. The bubbles progressively disappear and the mixture returns to its initial volume after 5 to 10 minutes. Wait a few minutes to complete the degassing and then flash the vacuum. The silicone is ready for pouring, either by gravity or under low pressure.
Note: Flashing the vacuum once or twice accelerates the degassing. It is recommended to use a container with a high diameter / height ratio.
3. Polymerisation
The system polymerises at . The curing may be slowed down at lower temperature and contrary accelerated by heat.
Contact with certain materials can inhibit the crosslinking. See list below:

  • natural rubbers vulcanised with sulphur,
  • RTV 2 silicone elastomers catalysed with metal salts, e.g. tin-compounds,
  • PVC stabilised with tin salts and additives,
  • epoxy resins catalysed with amines.

In case of doubts, it is recommended to test the substrate by applying a small quantity of the mixed silicone on a restricted area.

 

STORAGE -10°C < t < +30°C IN ITS ORIGINAL PACK STIR WELL BEFORE USEStore in a cool, dry place with adequate ventilation. Keep away from incompatible materials, open flames, and high temperatures. Store in tightly closed original container. equipped with a degassing device. Suitable containers: polyethylene. Steel drums coated with epoxy-resin.Please consult the Safety Data Sheet of this product.Healthcare Class I;Skin Contact

SILBIONE RTV 4418 ADH B

SILBIONE RTV 4418 ADH A&B is a two component silicone elastomer that crosslinks at room temperature by polyaddition reaction. The polymerisation can be accelerated by heat.
The system can be used in combination with BLUESIL ADD 11013 to glue certain fabrics with silicones.
By addition of 0.2 wt.-% BLUESIL ADD 11013 the system sticks on vertical forms. The components are available as viscous liquids, which cure after mixing to a translucent, resistance and flexible material.

Adhesion;Bio-compatibility

2 Part RTV

Fluid

Healthcare Class I;Skin Contact

 

  • Outstanding adhesion between fabrics and silicones
  • Same elastic behaviour as the substrate silicones

 

 

  • Textile enforced prosthetic liners
  • Textile covered insoles

 

Asia Pacific;Central and South America;Europe Middle East Africa

For information about Storage and Shelf Life for this product, please download the Technical Data Sheet.

 Characteristics_A

 

 

Viscosity4500PairedCompISO 2555mPa.s
ColorTranslucentPairedCompEuropean Pharmacopea

 Characteristics_B

 

 

Viscosity14500PairedCompISO 2555mPa.s
ColorTranslucentPairedCompEuropean Pharmacopea

 

 

 Table_Characteristics_A_And_B

 

 

hardness_cd523e03-72a3-4261-93f9-36f7bbeeafb1hardness_cd523e03-72a3-4261-93f9-36f7bbeeafb1Hardness19.5PairedMixDIN 53505
elongation_68a5ddf2-2baf-4e60-ac6f-0a8a18a758b2elongation_68a5ddf2-2baf-4e60-ac6f-0a8a18a758b2Elongation> 550PairedMixDIN 53504%
pot-life_0d649a54-7503-4c7c-a047-9d0c4b3e9f6apot-life_0d649a54-7503-4c7c-a047-9d0c4b3e9f6aPot life55PairedMixmin
tear-strength_a14604f3-602f-4240-a9bf-15d90bbfbd13tear-strength_a14604f3-602f-4240-a9bf-15d90bbfbd13Tear strength> 15PairedMixDIN 53515N/mm

 

 

 

 

SILBIONE RTV 4418 ADH ASILBIONE RTV 4418 ADH A/our_offer/Product/90051492/90051493/SILBIONE-RTV-4418-ADH-A

 

 

 

 

 NeedAnExpert

 

 

 CS

 

 

 SS

 

 

 PressRelease

 

 

 

 

 Brochures

 

 

Othotics & Prostheticshttps://silicones.elkem.com/EN/Our_offer/KEC/ListInstance_Brochure_Title/OP_Flyer.pdfOthotics & Prosthetics

 TDS

 

 

 

 

 

 

 

$Resources:BSIemotion,footer_Imageimplementations_alt;
Top

All rights reserved © Elkem Silicones 2018