Product

 

 

SILBIONE RTV 4525 SB A may be stored at a temperature between -10 °C/ 14 °F and 30 °C/ 86 °F for up to 6 months from its date of manufacturing.Please consult the Safety Data Sheet of this product.

SILBIONE RTV 4525 SB A

SILBIONE RTV 4525 SB A&B is a two component oil-bleeding silicone elastomer which cures at room temperature by a polyaddition reaction. The polymerisation can be accelerated by heat.

The silicone material is delivered as two low viscous liquid components, which once mixed and cured, transform into an elastic and resistant material. Polymerisation occurs without formation of heat.

Bio-compatibility

2 Part RTV

Fluid

  • ​Oil-bleeding for selected properties.
  • Sterilisable.
  • Fast mixing and easy processing due to low viscosity.

Liners for limb prostheses.

Asia Pacific;Europe Middle East Africa;Central and South America;North America

 Characteristics_A

 

 

Viscosity1400PairedCompISO 2555mPa.s
ColorTranslucentPairedCompEuropean Pharmacopea

 Characteristics_B

 

 

Viscosity1400PairedCompISO 2555mPa.s
ColorTranslucentPairedCompEuropean Pharmacopea

 

 

 Table_Characteristics_A_And_B

 

 

hardness_cd523e03-72a3-4261-93f9-36f7bbeeafb1hardness_cd523e03-72a3-4261-93f9-36f7bbeeafb1Hardness25PairedMix
pot-life_0d649a54-7503-4c7c-a047-9d0c4b3e9f6apot-life_0d649a54-7503-4c7c-a047-9d0c4b3e9f6aPot life120PairedMixmin

 

 

 

 

SILBIONE RTV 4525 SB BSILBIONE RTV 4525 SB B/our_offer/Product/90050451/90050452/SILBIONE-RTV-4525-SB-B

 

 

​Remix each of the two components (part A and B) every time before using.

1. Mixing the two components

The components A and B are mixed by weight in the above indicated ratio. The mixing can be carried out either by hand or by using a low-speed electric or pneumatic mixer to minimise the introduction of air and to avoid any temperature increase.

It is also possible to use a special mixing and dispensing machine for the two silicone components. Further information is available upon request.

2. Degassing

The mixture should be degassed preferably at 30 to 50 mbar to eliminate any entrapped air. If a dispensing machine is used, the two components are degassed separately prior to mixing.

The silicone mixture expands 3 to 4 times its initial volume and bubbles rise to the surface. Wait a few minutes to complete the degassing and then release the vacuum. The silicone is ready for pouring, either by gravity or under low pressure.

Note: Release the vacuum once or twice accelerates the degassing. It is recommended to use a container with a high diameter / height ratio.

3. Polymerisation

The system polymerises at 23 °C. The curing may be slowed down at lower temperature or accelerated by heat. The oil-bleeding occurs within 24 h.                                            

Contact with certain materials can inhibit the crosslinking. See list below:

  • Natural rubbers vulcanised with sulphur.

  • RTV 2 silicone elastomers catalysed with metal salts, e.g. tin-compounds.

  • PVC stabilised with tin salts and additives.

  • Epoxy resins catalysed with amines.

In case of doubts, it is recommended to test the substrate by applying a small quantity of the mixed silicone on a restricted area.

​Remix each of the two components (part A and B) every time before using.1. Mixing the two componentsThe components A and B are mixed by weight in the above indicated ratio. The mixing can be carried out either by hand or by using a low-speed electric or pneumatic mixer to minimise the introduction of air and to avoid any temperature increase.It is also possible to use a special mixing and dispensing machine for the two silicone components. Further information is available upon request.2. Degassing The mixture should be degassed preferably at 30 to 50 mbar to eliminate any entrapped air. If a dispensing machine is used, the two components are degassed separately prior to mixing.The silicone mixture expands 3 to 4 times its initial volume and bubbles rise to the surface. Wait a few minutes to complete the degassing and then release the vacuum. The silicone is ready for pouring, either by gravity or under low pressure.Note Release the vacuum once or twice accelerates the degassing. It is recommended to use a container with a high diameter / height ratio.3. PolymerisationThe system polymerises at 23 °C. The curing may be slowed down at lower temperature or accelerated by heat. The oil-bleeding occurs within 24 h. Contact with certain materials can inhibit the crosslinking. See list belowNatural rubbers vulcanised with sulphur.RTV 2 silicone elastomers catalysed with metal salts, e.g. tin-compounds.PVC stabilised with tin salts and additives.Epoxy resins catalysed with amines.In case of doubts, it is recommended to test the substrate by applying a small quantity of the mixed silicone on a restricted area.

 

 

​Remix each of the two components (part A and B) every time before using.

1. Mixing the two components

The components A and B are mixed by weight in the above indicated ratio. The mixing can be carried out either by hand or by using a low-speed electric or pneumatic mixer to minimise the introduction of air and to avoid any temperature increase.

It is also possible to use a special mixing and dispensing machine for the two silicone components. Further information is available upon request.

2. Degassing

The mixture should be degassed preferably at 30 to 50 mbar to eliminate any entrapped air. If a dispensing machine is used, the two components are degassed separately prior to mixing.

The silicone mixture expands 3 to 4 times its initial volume and bubbles rise to the surface. Wait a few minutes to complete the degassing and then release the vacuum. The silicone is ready for pouring, either by gravity or under low pressure.

Note: Release the vacuum once or twice accelerates the degassing. It is recommended to use a container with a high diameter / height ratio.

3. Polymerisation

The system polymerises at 23 °C. The curing may be slowed down at lower temperature or accelerated by heat. The oil-bleeding occurs within 24 h.                                            

Contact with certain materials can inhibit the crosslinking. See list below:

  • Natural rubbers vulcanised with sulphur.

  • RTV 2 silicone elastomers catalysed with metal salts, e.g. tin-compounds.

  • PVC stabilised with tin salts and additives.

  • Epoxy resins catalysed with amines.

In case of doubts, it is recommended to test the substrate by applying a small quantity of the mixed silicone on a restricted area.

​Remix each of the two components (part A and B) every time before using.1. Mixing the two componentsThe components A and B are mixed by weight in the above indicated ratio. The mixing can be carried out either by hand or by using a low-speed electric or pneumatic mixer to minimise the introduction of air and to avoid any temperature increase.It is also possible to use a special mixing and dispensing machine for the two silicone components. Further information is available upon request.2. Degassing The mixture should be degassed preferably at 30 to 50 mbar to eliminate any entrapped air. If a dispensing machine is used, the two components are degassed separately prior to mixing.The silicone mixture expands 3 to 4 times its initial volume and bubbles rise to the surface. Wait a few minutes to complete the degassing and then release the vacuum. The silicone is ready for pouring, either by gravity or under low pressure.Note Release the vacuum once or twice accelerates the degassing. It is recommended to use a container with a high diameter / height ratio.3. PolymerisationThe system polymerises at 23 °C. The curing may be slowed down at lower temperature or accelerated by heat. The oil-bleeding occurs within 24 h. Contact with certain materials can inhibit the crosslinking. See list belowNatural rubbers vulcanised with sulphur.RTV 2 silicone elastomers catalysed with metal salts, e.g. tin-compounds.PVC stabilised with tin salts and additives.Epoxy resins catalysed with amines.In case of doubts, it is recommended to test the substrate by applying a small quantity of the mixed silicone on a restricted area.

 NeedAnExpert

 

 

 CS

 

 

 SS

 

 

 PressRelease

 

 

 

 

 Brochures

 

 

 TDS

 

 

 

 

 

 

 

$Resources:BSIemotion,footer_Imageimplementations_alt;
Top

All rights reserved © Elkem Silicones 2018